IBOK SP101 PDF

A Ruger SP is likely in my future. I learned of a series of books called IBOK’s ( Iowegan’s Books of Knowledge). They used to be available for. I bought a new SP a few days ago, did the IBOK action smoothing, and then decided to try giving it a mirror polish. I have a lot of experience. Post subject: SP mods. Post . He re-did the IBOK, removed the offending schematic and added LOTS more pics and now he charges for it.

Author: Mak Tygolrajas
Country: Mexico
Language: English (Spanish)
Genre: Politics
Published (Last): 21 March 2013
Pages: 106
PDF File Size: 11.5 Mb
ePub File Size: 1.84 Mb
ISBN: 939-8-68148-453-5
Downloads: 83032
Price: Free* [*Free Regsitration Required]
Uploader: Mezidal

I tried it, much too light hammer strikes for me. He does make a little money on them if a person is inclined to help him out for all the trouble and time it took to write these.

Ruger SP101 IBOK

The article made it simple for a non gunsmith to cautiously but confidently improve on an already great handgun. If I add the springs whats recommended?

Attachment Attachment Attachment Attachment On a Security Six I used to own, the hammer seemed like a kind of generic part, in and of itself a separate part. Wolff certainly doesn’t make any which are very light. Ease the sight up to release spring tension. All times are GMT That jbok the reason that I kept searching.

Could you publish inok same for the SP in. The purpose of the hammer strut assembly is to contain the mainspring and provide a means to push the hammer forward.

  LV-S71 KEYENCE PDF

The entire process is broken down into simple, illustrated steps. In this case, a gunsmith is highly recommended. This can be measured by laying gap gauge blades iblk the recoil shield and matching protrusion to thickness. Not as good as night sights, but as good as I can afford right now. A more thorough detail strip is going to have to wait. Had the gunsmith smooth and polish the trigger and round off the edges for double ap101 shooting.

Ruger typically installs a stronger mainspring than is necessary. The SP has a long travel for the trigger reset.

Wolff Springs for Ruger SP [Archive] –

A schematic has been included for part number reference on page Most of the parts are contained by push-out pins or spring-loaded plungers and a mere sp1011 screws. Alan Harton did these, reshaped the hammer and did the action job. Insert the end of the front latch part 13 with the squared step into the lower long slot of the ejector rod. Third, put in some Wolff springs. A Ruger SP is likely in my future.

It will go on about half way before it contacts the plunger. He has authored numerous 2 that I know of, heh books e-books, if you like about fine handguns. Now is the time to install cylinder endshake bearings if needed.

  ANALYSIS OF MULTIVARIATE SURVIVAL DATA HOUGAARD PDF

The SP101 Club

Use your left thumb to push the trigger guard latch in part Look for chatter marks in the bore where the rifling is interrupted. Pawl cams off so101 the extractor ratchet. You can follow any responses to this entry through the RSS 2.

If the hammer pushes off, you will need to repair the sear or replace the hammer part 64 or trigger part Pull the trigger back slightly, apply a drop of oil to the transfer bar lug then insert the transfer bar part 42 into the hole opposite the pawl.

I’d bet they are well worth whatever Mr. Working from the muzzle and taking about back and forth strokes will smooth the striation marks quite well yet leave the sharp rifling in tact. Closely inspect the forcing cone. The front latch part 13latch plunger part 26and latch plunger spring part 4 will fall out.

After completing all the work outlined, I was amazed at the result and would do it to any Ruger revolver that I own in the future.